This post may contain affiliate and/or sponsored links.
Did you catch my tutorial on how I made these awesome shaker style cabinet doors for under $20?
Then you’re in the right place!
This is step two of the process.
Now that my gorgeous new cabinet doors are built and cured, they’re ready to be painted and installed.
I’ll be honest, I was a little nervous about painting them with a brush.
I usually use a sprayer but I’m in the process of organizing the garage and I can’t exactly get to it right now.
(I know, a kitchen update AND a garage organization project at the same time? I’m a madwoman.)
But as I began painting, I actually think I like this way better.
I used the fancy schmancy technique of rising the cabinet doors off the floor by balancing them on jars of canned veggies and fruit.
You can use anything you have around the house, you just need to make sure they’re at least 6 inches off the floor.
Nothing is worse than paint “gluing” your doors to the floor and ruining all your hard work.
The cabinet doors had some leftover dust from all the sanding I did during the building process, so I gave them a good rubdown with a microfiber cloth.
It’s also a good idea to clean them with a pre-painting cleaner like TSP to ensure there is no grease or oil hiding out on the surface.
It’s not completely necessary since you’ve already sanded down the door face, but it doesn’t hurt at all.
Better safe than sorry.
Now here’s where things get technical.
In order to get the best paint job with the minimal amount of streaks and brush strokes, you’ve got to follow this exact order.
Start by painting with a brush around the inside edges of the door frame.
Next, roll on a thin layer of paint in the middle.
This smooths out your brush lines around the edges.
It’s just like painting walls, where you’d cut in, then roll over.
Back to the brush again!
Paint the edges all the way around being careful not to let the paint glob up.
Those globs will drip and look uneven and unprofessional when the doors dry.
And now we’re back to the roller again.
Roll on a layer of paint onto the shaker frame front.
After the layer of paint has dried, start over and do another coat.
If you’re using a good thick paint with primer, two coats should be all you’ll need, but no worries if you need to pop on one more for safety.
Then you’ll paint on two coats of Polycrylic (not polyurathane, it yellows on white paint) according to the instructions on the can.
Let that dry for 48 hours before installing the hardware and putting the doors back up.
This is a great time to give your cabinets a fresh coat of paint, too.
Speaking of hardware, let me introduce you to my secret weapon.
Reality check, eyeballing doesn’t work.
You’ll never, and I mean NEVER get it even.
I found this great plastic template from my local hardware store for around $5 and it was well-worth the money.
Every single knob or handle will be perfectly lined up, making you look like a freakin’ pro.
You can find these templates near the cabinet pulls at your store, or you can buy one here.
Pop a little strip of painters tape over the spot you’ll be drilling the hole to prevent any wood splitting.
The worst thing ever is to do all that work, then have your wood split and have to spend an hour fixing it.
You’ll just use the template to mark your drill spot with an extra fine tipped pen or marker.
Extra extra fine.
The holes on the one I bought were teeny tiny.
Next up, remove the template and drill your hole.
Check with your cabinet pulls to see what size hole you need.
If you bought new ones, the package should tell you.
If you’re reusing old ones, you can compare the screw with the drill bit for the best fit.
Go one size small than you think you should, then test the screw.
You can always make the hole bigger, but you can never make the hole smaller.
And that’s it my friends!
You are now officially ready to add your hinges, put the cabinets back up, and put on your knobs.
Once you’re finished, stand back and be amazed that you actually did that.
Take a picture and post it.
You deserve to brag!
Speaking of bragging, what do you think about my door and drawer pulls?
Look expensive, huh?
They actually aren’t! I found this awesome company on Amazon that offers all kinds of sizes for amazing prices.
They look just like the ones in designer homes but were a third of the price.
Want to follow along with my low-cost kitchen renovation?
Check out these other posts I shared during the process.
Coming Soon: How To Install Tile Backsplash On A Budget AND My Kitchen Reveal!
Don’t miss them! Subscribe to my email list so you’ll get updates straight in your inbox.
**This post contains affiliate links. By purchasing from these links, a small commission is paid to In The New House Designs, at no extra cost to you. Your purchase helps fund this website and allows me to provide you with more awesome DIYs. All opinions are my own and I only endorse products I absolutely love. For more information on affiliate links, view my Disclosure page.
Join The DIY Design Club
Get instant access to the DIY Design Club Resource Library filled with all of my best tips, tricks, printables, and tutorials. This exclusive content is for members only, and it's free to join!